Install pocket door latch

Quick and easy without open. Your email address will not be published. About Contact Privacy Police. How to. Toggle Navigation. Share your thoughts Cancel reply Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. Tags account after become braces cancel carpet change clean cook cost does door find from garage hair have home install iphone keep long make much often open paint play pool pronounce reddit remove replace reset someone start stop take teeth turn watch water with without your.

Recent Comments. Pages About Contact Privacy Police. Categories how to. You can use any standard door with a pocket door kit as long as the following requirements are met:. The weight of the door must not be greater than the weight specified by the manufacturer of the kit. The dimensions of the door must be small enough to fit within the pocket. Fire door. Because the door is not a tight fit when closed, it is no use as a fire door.

Door material. Although it is possible to install an internal flush door as a pocket door, eventually the top rail from which the door hangs will work loose and may be pulled out of the door. Ready cut hardware. Doors with ready cut rebates and mortices cannot be used as pocket doors because the sliding door hardware would not fit. The cost to buy a pocket door kit will depend on the quality.

Better quality kits, although costing more at the start will always pay back in ease of use and reduction in maintenance. For example a top quality heavy duty, ball bearing or nylon roller which is guaranteed to stay on the tracks together with aluminium wrapped split studs designed to stop warping, will pretty much solve all the negative comments aimed at pocket doors. The type of door and hardware such as flush handles and a locking latch need to be well made too or you will regret it when things start to go wrong later on.

You will also have to purchase additional studs and lintel for the framing as well as a few sheets of gypsum plasterboard to make good the wall afterwards. When you go shopping for a DIY kit on how to install a pocket door, there are a number of things you should look out for.

Make sure the manufacturer has supplied well written and understandable instructions. Some manufacturers supply a DVD showing video footage of the correct installation method. These are indispensable and should not be sneered at. Even if you have installed a pocket door before, all brands are different and require specific instructions on how to install your particular type.

What type? Pocket doors that use steel rollers tend to be very noisy and will often jump off the tracks. You should be looking for axle mounted nylon rollers or ball bearing rollers and metal tracks.

Type of door? Because of this wide range of available hardware strengths it is possible to choose almost any interior domestic style door including flush, louvred, glazed, mirrored or panel. Your new pocket door will be sliding in and out of a hole in the wall for many years so you want one that is going to be relatively problem free. Look for these features.

A good quality kit will have these specific features and you should specifically look for them:. We have already said that pocket doors are good because they allow you to have a door opening when there is little space available. By their very nature however, pocket doors do not fit tight in their frames and will always allow cold draughts and light pollution to invade your warm and snug home. To fix this problem you will have to learn how to seal the door to prevent cold air and unwanted light from entering and leaving a room.

The first step in sealing your door is to identify what is causing the draught. Have a look around the pocket door and see if you can see anything obvious that might be allowing cold air to come through.

Fixing the pocket gap. You will often find that the pocket in the wall is itself one of the biggest causes of cold air movement. You will have to find a way of insulating any gaps between the door and the pocket opening. The best way to attempt this is to use the brush type draught excluder which will mould themselves around the door and allow it free movement along its track while still blocking off any openings. These brushes will effectively stop any draughts in whatever position the door is left.

Is there a gap under the door? You may find that another possible location for a draught is from under the door. You will realise by now that pocket doors fit into rails or guides fixed onto the floor which allow the door to open and close along a predetermined route. You can fit brush type draught excluders along the bottom of the door to prevent any cold air from this location. Is there a gap above the door?

If you have a gap above the door you can fix this in exactly the same way. Is there a gap on the lock jamb? When the door is closed and is tight up against the lock jamb of the frame or lining you will see if there is any gap between the edge of the door and the door lining. There usually is a gap, so once again you can use brush type draught excluders or lengths of wooden doorstop screwed to the jamb. Test your seals. Once you have sealed everything obvious you will have to determine if you can still feel cold air.

If you can, you will have to go over the process once again to see if anything has been missed. Light seals. In the same way but using slightly different seals, you will be able to block any gaps to stop unwanted light as well.

Pocket doors are a brilliant idea and used to be very popular up until Interest in them declined as the fashion changed and people realised they were more trouble than they were worth. Recently with modern plastics and manufacturing methods it has been possible to produce pocket door kits that no longer suffer from the same problems and they are gaining in popularity once more.

This article has told you a bit about pocket doors, their advantages and disadvantages and how to install them correctly. What is a pocket door for? They are sleek and streamlined and give the impression of planned elegance.

Certainly, steel better resists high impacts and wear, which ensures a long lifespan. Brass models are also good, but tend to fail in the first months of use.

First of all, try to have the necessary tools at hand to get the job done. In most cases, to install a pocket door lock you only need to have the following:. Before doing any work, be sure to wear the appropriate safety equipment, including gloves, glasses and face mask.

Once you have all the necessary tools at hand and the safety conditions are a guarantee, it is time to start working. Just follow these steps:.

If the lock and pull are separate pieces, install the pull on its corresponding place, applying the same procedure in this guide. As you can see, installing a pocket door lock is a quick and simple procedure.

If you have the right tools, you can finish the job faster than you think. During installation, try to be careful and use the required safety equipment.

See the articles ' Adjusting Pocket Doors ' and ' Troubleshooting Pocket Door Problems ' for a listing of possible repairs that may solve your problem. You can find pocket door latches or locks on the internet and at home supply stores. They are about the same price as a conventional lockset. There are not nearly as many options with pocket door locks as you have with regular swinging doors. You may find the selection and functionality somewhat limited. When replacing the door lock, you need to get one that is the same size as the old one.

There is not a lot of door left around the lock for the cover plates to seat on. A lock that is too small will not cover the mortise. It would be a good idea to take the old lock with you when you go shopping.

A Pocket door lock is held together with screws. There are probably four screws that are toward the center of the door that hold the lock assembly to the door.